JConcepts Garage

You are here

10th Scale Buggy Drawstring Tote Bag

Project By

Chilly

When traveling to the track most of today’s drivers want something to transport their vehicle in. This way they can protect it from the elements like rain, or make it easier to carry into the pits along with all of their other racing equipment. The most popular racing classes still in 1/10 electric off-road are 2WD and 4WD buggy. Even with these somewhat smaller vehicles, pit space can be limited at the track. So if you arrive at the track and get settled in, the last thing you want to worry about is where to store your bulky, car carrier before you go turn some laps. So drivers have requested a new, simple option to address these common issues, and in this edition of the Garage we’ll go over a new product from JConcepts that has these issues “in the bag”.

The JConcepts 1/10 Buggy Drawstring Tote Bag is comprised of black, water-resistant fabric.

An official JConcepts Racing Team logo is screened on one side of the bag and rests below an integrated storage pocket.

The pocket is sealed tight with a metal zipper system which has a 2” piece of fabric attached to it. This helps you to navigate the zipper back and forth and the gray material is also reflective too.

When unzipped this deep pocket nearly runs the entire length of the bag and gives you ample space to store items inside.

On the bottom rests a thick, vinyl coating that helps to protect the bag from the elements and resists tearing. 

Centered right above it on the logo side of the bag is a small section with ventilation holes.

Sewn directly into on each side of the vinyl strip are beefy drawstrings.

These drawstrings run the length of the bag and meet at the top where the opening of the bag is located. The water resistant material is then sewn over the drawstrings to properly route them into place.

 A quick tug of the strings on both sides quickly closes the opening to the 1/10 Buggy Drawstring Tote Bag. 

If you gently pull back the material around the opening inside you will find two large “sleeves”. With the logo side of the bag facing up, the top “sleeve” runs the entire length of the bag while the bottom one runs almost the entire length.

The top “sleeve” was intended to store your buggy in since you are allotted more room, and a buggy will rest inside with the tires, body, and wing still installed. The bottom sleeve is commonly used for setup sheets, manuals, or anything else you want to store in there.

But this bag offers you a lot of options so you may find it works better to store the manual in the top pocket along with some tools.

Or you can decide to store only your essential tools there instead.

If you are only traveling to the track for a club race you might want to use it to store some race tires.

Or it might be a handy spot for your JConcepts Small Zipper Pouch that you keep your tire mounting materials in.

Maybe you would rather have the manual and tools stored below in the shorter “sleeve”.

The JConcepts 1/10 Buggy Drawstring Tote Bag holds lots of options so just choose the best one that floats your tote. I hope you enjoyed this edition of the Garage, and a complete list of the items featured in this story is listed below:

JConcepts Products: 

0341 - P2 - B6 | B6D | B6.1 High-Speed Body - MSRP $33.00 
2029 - JConcepts Racing Banner - MSRP $20.00
2133 - 4' Pit Mat – MSRP $20.00
2212-1 - Satellite Tire Rubber Bands - Blue - MSRP $13.00
2212-2 - Satellite Tire Rubber Bands - Black - MSRP $13.00
2212-6 - Satellite Tire Rubber Bands - Orange - MSRP $14.00
2212-7 - Satellite Tire Rubber Bands - Red - MSRP $14.00
2212-8 - Satellite Tire Rubber Bands - Gray - MSRP $14.00
2250-7 - JConcepts Parts Tray - Red - MSRP $16.00
2263-1 – 7mm Fin Quick-Spin Wrench - Blue - MSRP $25.00
2284 - 10th Scale Buggy Drawstring Tote Bag - MSRP $25.00
2341-2 - 4mm Large Flange Serrated Locknut – Black – MSRP $22.00
2405 - B6.1 | B6.1D, Carbon Fiber Gullwing Arm Front Shock Tower - MSRP $27.00
2406 - B6.1 | B6.1D, Carbon Fiber Rear Shock Tower – Standard - MSRP $34.00
2409-2 - B6.1 | B6.1D | T6.1 | SC6.1 Rear Ball-Stud Mount - Black - MSRP $16.00
2430-1 – 10th Scale Off-Road Tire Stick – Blue - MSRP $15.00
2452-2 – Fin Reamer - Black - MSRP $45.00
2490-2 – Fin - 12mm V2 Shock Cap – B5M, T5M, SC5M - Black – MSRP $15.00
2491-2 – Fin - 12mm Shock Collar – B5M, T5M, SC5M - Black – MSRP $8.00
2492-2 – Fin - VCS Shock Bottom Cap – B5M, T5M, SC5M - Black – MSRP $8.00
2493-2 – Fin - Shock 5mm Off-Set Spring Cup – B5M, T5M, SC5M - Black – MSRP $15.00
2539 - Microfiber Towel - Blue / Black - MSRP $5.00
2552-1 - Precision Hobby Knife Handle - Blue - MSRP $36.00
2556-1 – Combo Thumb Wrench – Blue - MSRP $10.00
2568-2 - B6 | B6D | B6.1 Front Camber Link Mount Bulkhead – Black - MSRP $32.00
2572-2 - B6 | B6D | B6.1 Rear Suspension D Mount - Black - MSRP $12.00
2579-2 - B6 | B6D | B6.1 Finnisher Aluminum Wing Buttons - Black - MSRP $10.00
2580 - B6 | B6D Fin Titanium Turnbuckle Set – MSRP $45.00
2587-1 - Pinion Puck - Stock Range – Blue - MSRP $40.00
2599T - B6 | B6D | B64 Fin Titanium shock stand-offs w/ bushing – short - MSRP $20.00
2600T - B6 | B6D | B6.1 | B64 Fin Titanium Shock Stand-Offs Long - MSRP $20.00
3077-05 - Dirt Webs - Fits 2.2" 2wd Front Wheel – Gold - MSRP $23.00
3142-05 - Octagons - Buggy Rear – Gold -  MSRP $26.00
3143-05 - Octagons - 2wd Front – Gold - MSRP $26.00
3176-05 - Space Bars - Gold Compound (Fits 2.2" Buggy Rear Wheel) – MSRP $26.00
3177-05 - Space Bars - Gold Compound (Fits 2.2" Buggy Front Wheel) – MSRP $26.00
3196-06 - Ellipse - 2.2 Buggy Rear - Gold - MSRP $28.00
3347W - Mono - B4.1 | B5 | B6 | B6.1 | RB5 | RB6 | YZ2 | XB2 | RB7 - 12mm Hex Front Wheel – MSRP $13.00
3348 - Mono - B6.1 | B64 | RB7 | ZX7 | YZ2 | YZ4 | D418 | SRX2 | SDX4 - 12mm Hex Rear Wheel - MSRP $15.00

Dirt Racing Products: 

8111 - Dirt Cut – Recessed Ball-Stud Washer - Set – MSRP $23.00
8115 – Dirt Bands – Trie Gluing Rubber Bands – Yellow – MSRP $14.00
8116 - Dirt Racing Products – Permanent Dual Tip Pen Set - MSRP $5.00

Team Associated:

1349 - FT Aluminum Pinion Gear, 31T 48P, 1/8 shaft - MSRP $7.99
1350 - FT Aluminum Pinion Gear, 32T 48P, 1/8 shaft - MSRP $7.99
1351 - FT Aluminum Pinion Gear, 33T 48P, 1/8 shaft - MSRP $7.99
1352 - FT Aluminum Pinion Gear, 34T 48P, 1/8 shaft - MSRP $7.99
1353 - FT Aluminum Pinion Gear, 35T 48P, 1/8 shaft - MSRP $7.99
90021 - RC10B6.1D Team Kit - MSRP $469.99

Sources: http://www.jconcepts.net |http://www.teamassociated.com | #gojconcepts

 

Documents